Cooper-instruments-systems DFI INFINITY B Ultra High Performance Digital Forc Instrukcja Użytkownika Strona 1

DFI INFINITY B EMBEDDED ETHERNET SERVER OPTION USER’S GUIDE www.cooperinstruments.com PH: 540-349-4746 

7PART 3NETWORK CONFIGURATION3.1 Network ProtocolsThe iServer can be connected to the network using standard TCP/IP protocols. Italso supports ARP, H

83.3 DHCPDHCP, Dynamic Host Configuration Protocol enables individual computers or devices toextract their IP configurations from a server (DHCP serve

93.5 IP AddressEvery active device connected to the TCP/IP network must have a unique IP address.This IP address is used to build a connection to the

PART 4OPERATIONSAn industrial device with serial interfaces (PLC, CNC controllers, PC, Data DisplayDevices, etc.) can be connected to the serial port

Where:"*" is the selected Recognition Character. You may select any ASCII table symbol from"!" (HEX address "21") to the

4.4 OperationsThis iServer can be used and configured in several ways, depending on user’spreference and network setup. It can be used in Telnet simu

134.5 Setup and Operation Using a Web Browser (continued)Figure 4.2 Device TypeFigure 4.3 iServer Home Page MenuIn order to access certain menu ite

4.5.1 Read Devices• Read variables from up to eight different devices.• Read up to eight variables from the same device. • Read and write the setpoint

154.5.3 Device Setup• Device Setup helps you to see eight different variables or devices by “Check” box.• Up to four different devices or parameters c

164.5.4 Configuration• This section explains the Configuration page of the iServers’s Web interface.• When connecting your device to the iServer, the

TABLE OF CONTENTSPart 1: Introduction1.1 Safety and EMC Considerations...21.2 Des

4.5.4.A Serial Communication (continued)Transceiver: Can either be set to RS-232 or two-wire RS-485 (default is RS-232.)Modbus/TCP: A widely used prot

4.5.4.B Terminal Server (continued)Connection Control: Some serial devices accept connections or disconnectconnections based on certain signal condit

194.5.5 Access ControlThis section describes the "Access Control" page of the iServers’s Web interface. Thispage allows the users to set u

4.5.5 Access Control (continued)Host Name: Refer to Section 3.4, DNS.MAC Address: This is also called Hardware address or Ethernet address, which is

4.6 Setting a New IP Address over the NetworkThe iServer is shipped with a default IP address of 192.168.1.200 and Subnet Mask of255.255.255.0. You

224.7 Terminal Server FunctionIt is used to provide dedicated connectivity between computers and serial devicesthrough the iServer over the Ethernet,

4.8 Terminal Emulation On this page you can send and receive data to and from the instrument. Simply, type thecommand in the open window and as you t

244.9 Telnet SetupTelnet stands for Telecommunications Network, is a protocol that provides a way for users (orclients) to connect to computers (or s

4.9 Telnet Setup (continued)In the Configuration mode you can make any changes just like you would do using the WebBrowser. After connected to the i

264.10 HTTPGET ProgramYou can setup and read the information from the iServer by using the HTTPGETprogram. The following program can be used to read

LIST OF FIGURES:Figure 1.1 iServer on the Ethernet Network...3Figure 2.1 Rear Panel View

4.11 ARP ProtocolARP is the Internet layer protocol responsible for determining the MAC (hardware)address that corresponds to a particular IP address

4.12 Remote Access (Tunneling)To "tunnel", in this context, is to transmit data between two points through a privateconduit on a shared or

4.12.1 Remote iServer It’s recommended to configure the Remote iServer and have it up and running before theLocal iServer is configured.1. A static I

4.12.2 Local iServer 1. An IP address should be assigned to the iServer dynamically or statically (recommended).2. Use a browser to access the Local

314.13 Mail Notifier SoftwareThe Mail Notifier Software can be used only with NEWPORT Electronics instruments.For complete information of how to use

4.13.2 Program Options Setup and ConfigurationComplete program setup requires: • Entering a recipient for the email• Specifying connection details to

4.12.3 Device Setting and ConfigurationDevice setup requires:• Entering the IP address for iServer device (for example 192.168.1.200).• Specifying So

34PART 5SPECIFICATIONSNETWORK INTERFACE Interface: Ethernet 10 Base-TConnector: RJ45Protocols: ARP, TCP/IP, ICMP, DNS, DHCP, Telnet simulation and HTT

35PART 6FACTORY PRESET VALUESPRESET PARAMETERS FACTORY DEFAULTSNetwork Interface:IP Address 192.168.1.200Gateway Address 0.0.0.0Subnet Mask 255.255.25

36APPENDIX A GLOSSARYUser of this manual should be familiar with following definitions:ARP (Address Resolution Protocol) is a protocol for mapping an

NOTES, WARNINGS and CAUTIONSInformation that is especially important to note is identified by following labels:• NOTE • WARNING or CAUTION• IMPORTANT•

37Appendix B IP AddressAn IP address is a unique 32-bit address assigned to a computer and includes:• A network ID number identifying a network.• A ho

38Appendix C IP NetmaskIP Netmask or Subnet Mask is a 32-bit pattern of ones and zeros used to determinenetwork portion of an IP address from the host

39Appendix D ASCII ChartASCII Dec Hex Binary ASCII Dec Hex BinaryChar No Parity Char No parityNUL 00 00 00000000 @ 64 40 01000000SOH 01 01 00000001 A

40Appendix D ASCII Chart Continuation/ 47 2F 00101111 o 111 6F 011011110 48 30 00110000p112 70 011100001 49 31 00110001q113 71 011100012 50 32 0011001

41CE APPROVALS INFORMATIONThis product conforms to the EMC directive 89/336/EEC amended by93/68/EEC, and with the European Low Voltage Directive 72/23

WARRANTY REPAIR POLICY Limited Warranty on Products Any Cooper Instruments product which, under normal operating conditions, proves defective in mate

PART 1INTRODUCTION1.1 Safety and EMC ConsiderationsThis device is marked with the international caution symbol. It is important toread this manual bef

1.2 DescriptionThis iServer is designed to connect industrial devices with serial interfaces to theEthernet network using the TCP/IP protocol. It cont

4PART 2HARDWARE2.1 Physical Characteristics and MountingFor physical dimensions and installation instructions reference the Quickstart andOperator’s M

52.3 DIP Switches on the iServerFor Dipswitch access you must remove the main board from the case. Refer to theDisassembly Instructions in your Quicks

62.4 Network Communication Interfaces2.4.1 10Base-T RJ-45 PinoutThe 10BASE-T Ethernet network (RJ-45) system is used in the iServer for networkconnect