Cooper-instruments-systems Series M7 Professional Digital Force Gauge Instrukcja Użytkownika Strona 1

CF 194 M7 wwPH: (540 DigitalUseww.coope) 349-474l Force er Guid erinstrume 46 • FAX: e Gaugde ents.com(540) 347

Series 7 Digital Force Gauges User’s Guide 9 – the displayed value is greater than the upper force limit (NO GO HIGH) – the displayed v

Series 7 Digital Force Gauges User’s Guide 107.1 Configuration To enable Break Detection and configure the automatic functions, select Break

Series 7 Digital Force Gauges User’s Guide 11 7.3 Auto Output Settings Scroll to Auto Settings in the Break Detection menu and press ENTER to

Series 7 Digital Force Gauges User’s Guide 128.1 Real Time (RT) The primary reading corresponds to the live measured reading. 8.2 Peak Comp

Series 7 Digital Force Gauges User’s Guide 13Parameter Description Initial Delay The time delay, in seconds, before the averaging sequence co

Series 7 Digital Force Gauges User’s Guide 149.5 External Trigger (ET) This mode of operation is useful for measuring electrical contact acti

Series 7 Digital Force Gauges User’s Guide 159.5.1 External Trigger Schematic Diagram 14GND1IN22kSWITCH UNDER TESTGAUGE+3.3VTO MICROPROCESSO

Series 7 Digital Force Gauges User’s Guide 16 Select “+ More” for additional options: 9.6.3 Stop Condition Data capture is automaticall

Series 7 Digital Force Gauges User’s Guide 17 Note 2: Data capture may be manually stopped at any time by pressing the ZERO key. A message wi

Series 7 Digital Force Gauges User’s Guide 18 9.7.2 Peak Settings The display appears as follows: Thresholds and percentage drops are ill

Series 7 Digital Force Gauges User’s Guide 1Thank you… Thank you for purchasing a Mark-10 Series 7 digital force gauge, designed for tensio

Series 7 Digital Force Gauges User’s Guide 199.7.3 Auto Output Settings Scroll to Auto Output Settings and press ENTER to select the desired

Series 7 Digital Force Gauges User’s Guide 20the desired reading and press DELETE. The letter “D” appears to the left of the record number, i

Series 7 Digital Force Gauges User’s Guide 21 If no option is selected, this screen will be displayed indefinitely, or until battery power h

Series 7 Digital Force Gauges User’s Guide 2212 COEFFICIENT OF FRICTION Series 7 gauges can determine the static and kinetic coefficient

Series 7 Digital Force Gauges User’s Guide 23 14 COMMUNICATIONS AND OUTPUTS Communication with Series 7 force gauges is achieved through

Series 7 Digital Force Gauges User’s Guide 24 Selection Description Numeric + Units Output format includes the value and unit of measure.

Series 7 Digital Force Gauges User’s Guide 25 14.3 Analog Output This output can be used for chart recorders, oscilloscopes, data acquisition

Series 7 Digital Force Gauges User’s Guide 26** The output assignments depend on several factors described in the table below. Output functio

Series 7 Digital Force Gauges User’s Guide 27 Basic Functions CUR Current mode (real time mode) for primary reading PT Peak Tension

Series 7 Digital Force Gauges User’s Guide 28 ETLH Enable reading captured on a low to high transition ETD Disable External trigger m

Series 7 Digital Force Gauges User’s Guide 21 OVERVIEW 1.1 List of included items 1.2 Safety / Proper Usage Caution! Note the force gau

Series 7 Digital Force Gauges User’s Guide 29 The gauge can be calibrated at up to 10 points in each direction. Enter the number of calibrati

Series 7 Digital Force Gauges User’s Guide 30 If failed: 6. The following screen appears after the offsets have been calculate

Series 7 Digital Force Gauges User’s Guide 3110. The display appears as follows: Use the UP and DOWN keys to adjust the load valu

Series 7 Digital Force Gauges User’s Guide 3214. Any errors are reported by the following screens: Displayed at the start of ca

Series 7 Digital Force Gauges User’s Guide 3316 PASSWORDS Two separate passwords may be set to control access to the Calibration section a

Series 7 Digital Force Gauges User’s Guide 34 To re-enter the password, press ESC to exit to the home screen. Then, access the desired funct

Series 7 Digital Force Gauges User’s Guide 35 Selection Description Off Backlight to be off upon powering on the gauge. On Backlight to be on

Series 7 Digital Force Gauges User’s Guide 3617.6 Restore Default Settings Default factory settings can be restored by selecting Restore Defa

Series 7 Digital Force Gauges User’s Guide 3718.2 Factory Default Settings Parameter SettingSet points Upper Disabled (defaults to 80

Series 7 Digital Force Gauges User’s Guide 38 Keys Enabled Alerts Enabled Set Points Momentary Automatic Shutoff Enabled S

Series 7 Digital Force Gauges User’s Guide 3 6. In certain applications, such as the testing of brittle samples that can shatter, or other a

Series 7 Digital Force Gauges User’s Guide 3918.5 Dimensions IN [MM] Thread FlatM7-012 – M7-100 #10-32M UNF 5/16 [7.94] M7-200 – M7-50

Series 7 Digital Force Gauges User’s Guide 40 Mark-10 Corporation has been a

Series 7 Digital Force Gauges User’s Guide 43 SETUP 3.1 Mechanical Setup 3.1.1 Loading shaft orientation In order to accommodate a variet

Series 7 Digital Force Gauges User’s Guide 5such a way that it is prevented from slipping out during a test, preventing a potential safety ri

Series 7 Digital Force Gauges User’s Guide 64 Primary reading / Kinetic COF The current displayed force reading. When the COF unit is selecte

Series 7 Digital Force Gauges User’s Guide 74.2 Controls Primary Label Primary Function Secondary Label Secondary Function Powers the gauge

Series 7 Digital Force Gauges User’s Guide 8 Two filters are available: Current Reading – Applies to the peak capture rate of the instrumen